<
From version < 16.1 >
edited by Fredrik Lagerström
on 2021/01/13 08:46
To version < 17.1 >
edited by Fredrik Lagerström
on 2021/01/13 09:01
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2,36 +2,70 @@
2 2  {{toc/}}
3 3  {{/box}}
4 4  
5 -When you're done calculating a PRE-Stress project, the data can be published as a report. This is done through the Preview & Print functionality in the File menu. The printout can then be sent to any print-capable device recognized by your operating system, including fax utilities and pdf conversion tools.
5 +When you're done calculating a PRE-Stress project, the data can be published as a report. This is done through the Preview & Print functionality in the File menu. The printout can then be sent to any print-capable device recognized by your operating system.
6 6  
7 7  (% id="cke_bm_480S" style="display:none" %) (%%)As the calculation and dimensioning process generates a large volume of information, PRE-Stress allows you to filter the printout to contain the information most relevant to a given project.
8 8  
9 -[[image:1610520959086-866.png]]
9 +== Printout options ==
10 10  
11 -The printout selection tab allows you to enable or disable various aspects of the printout. Each of these aspects are handled by their own tab, which allows for more precise printout configuration.
11 +=== Settings for beams ===
12 12  
13 -[[image:1610520975221-515.png]]
13 +[[image:1610523934439-194.png]]
14 14  
15 -This section determines which aspect(s) of the geometry data, if any, should be printed out.
15 +The settings can be set for each individual element.
16 16  
17 -[[image:1610520995914-100.png]]
17 +The settings that can be selected are:
18 18  
19 -This section determines which aspect(s) of the load-related data, if any, should be printed out.
19 +* General information
20 +* Reinforcement
21 +* Cross-section data
22 +* Supports
23 +* Loads
24 +* Calculation settings
25 +* Fire
26 +* Loadcases per load combination
27 +** Explanation
28 +* Max bending table
29 +** Explanation
30 +* Max shear table
31 +** Explanation
32 +* Recess beam
20 20  
21 -(% id="cke_bm_505S" style="display:none" %) (%%)The following sections similarly deal with their own aspects, but on an element- or load combination basis.
34 +[[image:1610523967065-192.png]]
22 22  
23 -[[image:1610521015164-856.png]]
36 +Each load combination also has individual settings. these might be dependant on what type of element that is being calculated, if topping is present, if it is subjected to torsion or if a punching check can be performed (hollowcore elements with point loads)
24 24  
25 -[[image:1610521111128-304.png]]
38 +The settings here are:
26 26  
27 -[[image:1610521126915-786.png]]
40 +* General material settings
41 +* Long term parameters
42 +* Moment/shear tables
43 +** Explanation
44 +* Moment/shear tables (topping)
45 +** Explanation
46 +* Topping joint table
47 +** Explanation
48 +* Reduced concrete parameters (fire)
49 +** Explanation
50 +* Torsion table
51 +** Explanation
52 +* Punching
28 28  
29 -[[image:1610521165149-492.png]]
54 +It is also possible to add diagrams
30 30  
31 -[[image:1610521184169-200.png]]
56 +* Moment
57 +* Shear
58 +* Deformation
59 +* Torsion
32 32  
33 -[[image:1610521197967-450.png]]
34 34  
35 -[[image:1610521211935-869.png]]
36 36  
63 +
64 +
65 +
66 +
67 +
68 +
69 +
70 +
37 37  In addition, selecting File-> Print general overview will generate and print an overview report, which is a condensed summary of the project data
Copyright 2020 StruSoft AB
PRE-Stress Documentation